Port 1127 KWDB-COMMN
Port 1127 is the IANA-assigned kwdb-commn port for KWDB Remote Communication (TCP / UDP).
What is port 1127 used for?
Port 1127 is assigned to kwdb-commn and uses TCP / UDP. The IANA registry describes the service as “KWDB Remote Communication”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach kwdb-commn connects to port 1127. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 1127 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Lal_Samuel_Varghese].
Check and block port 1127
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :1127'
sudo ss -ulpn 'sport = :1127'Check on Windows
Get-NetTCPConnection -LocalPort 1127 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 1127 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 1127/tcp
sudo ufw deny 1127/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 1127 -j DROP
sudo iptables -A INPUT -p udp --dport 1127 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 1127 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 1127 is usually used
Most traffic on port 1127 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Application backends and supporting services that use a fixed registered number.
- Containers or local stacks that publish the port on the host.
- Firewall and exposure reviews before the service goes to production.
Probe the port
Confirm something is listening before you debug the client. This checks a TCP handshake on the port.
nc -vz 127.0.0.1 1127Common problems with port 1127
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 1127. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :1127' or sudo lsof -i :1127. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 1127 at a glance
| Port number | 1127 |
|---|---|
| Service name | kwdb-commn |
| Transport protocol | TCP / UDP |
| Category | Application services |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [Lal_Samuel_Varghese] |
| Registry description | KWDB Remote Communication |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 1127 used for?
Port 1127 (KWDB-COMMN) uses TCP / UDP. KWDB Remote Communication.
How do I check if port 1127 is open?
On Linux run `sudo ss -tlpn 'sport = :1127'` and `sudo ss -ulpn 'sport = :1127'`. On Windows run `Get-NetTCPConnection -LocalPort 1127 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 1127 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 1127; empty output usually means nothing is bound to it.
How do I block port 1127?
With UFW run `sudo ufw deny 1127/tcp` and `sudo ufw deny 1127/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 1127 -j DROP` and `sudo iptables -A INPUT -p udp --dport 1127 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 1127 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 1120 · bnetfileBattle.net File Transfer Protocol
- Port 1128 · saphostctrlSAPHostControl over SOAP/HTTP
- Port 1119 · bnetgameBattle.net Chat/Game Protocol
- Port 1131 · caspsslCAC App Service Protocol Encripted
- Port 1113 · ltp-deepspaceLicklider Transmission Protocol
- Port 1132 · kvm-via-ipKVM-via-IP Management Service
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy