Port 1918 CAN-NDS
Port 1918 is the IANA-assigned can-nds port for IBM Tivole Directory Service - NDS (TCP / UDP).
What is port 1918 used for?
Port 1918 is assigned to can-nds and uses TCP / UDP. The IANA registry describes the service as “IBM Tivole Directory Service - NDS”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach can-nds connects to port 1918. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 1918 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Browse all Directory services ports
Source: IANA Service Name and Transport Protocol Port Number Registry.
Check and block port 1918
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :1918'
sudo ss -ulpn 'sport = :1918'Check on Windows
Get-NetTCPConnection -LocalPort 1918 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 1918 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 1918/tcp
sudo ufw deny 1918/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 1918 -j DROP
sudo iptables -A INPUT -p udp --dport 1918 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 1918 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 1918 is usually used
Most traffic on port 1918 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Applications authenticating users against a central directory.
- Single sign-on, group lookups and address-book integrations.
- Administrators querying or syncing directory entries from a bastion host.
Read the root DSE
The root DSE confirms the directory is answering before you test a specific base DN.
ldapsearch -H ldap://127.0.0.1:1918 -x -b "" -s base namingContextsCommon problems with port 1918
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 1918. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :1918' or sudo lsof -i :1918. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 1918 at a glance
| Port number | 1918 |
|---|---|
| Service name | can-nds |
| Transport protocol | TCP / UDP |
| Category | Directory services |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | Not listed |
| Registry description | IBM Tivole Directory Service - NDS |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 1918 used for?
Port 1918 (CAN-NDS) uses TCP / UDP. IBM Tivole Directory Service - NDS.
How do I check if port 1918 is open?
On Linux run `sudo ss -tlpn 'sport = :1918'` and `sudo ss -ulpn 'sport = :1918'`. On Windows run `Get-NetTCPConnection -LocalPort 1918 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 1918 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 1918; empty output usually means nothing is bound to it.
How do I block port 1918?
With UFW run `sudo ufw deny 1918/tcp` and `sudo ufw deny 1918/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 1918 -j DROP` and `sudo iptables -A INPUT -p udp --dport 1918 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 1918 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 1911 · mtpStarlight Networks Multimedia Transport Protocol
- Port 1919 · can-dchIBM Tivoli Directory Service - DCH
- Port 1525 · prospero-npProspero Directory Service non-priv
- Port 636 · ldapsldap protocol over TLS/SSL (was sldap)
- Port 1920 · can-ferretIBM Tivoli Directory Service - FERRET
- Port 389 · ldapLightweight Directory Access Protocol
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy