PortAtlas.
Registered port (1024–10000) Standard/Low risk

Port 4405 DS-MAIL

Quick answer

Port 4405 is the IANA-assigned ds-mail port for ASIGRA Televaulting Message Level Restore service (TCP / UDP).

Check and block Is it safe? Troubleshooting FAQ
TransportTCP / UDP
RiskStandard/Low
Typical useInfrastructure and administration

What is port 4405 used for?

Port 4405 is assigned to ds-mail and uses TCP / UDP. The IANA registry describes the service as “ASIGRA Televaulting Message Level Restore service”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.

Ports are the transport-layer address a service listens on. A client that wants to reach ds-mail connects to port 4405. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.

Use the commands below to confirm whether port 4405 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.

Browse all Infrastructure and administration ports

Source: IANA Service Name and Transport Protocol Port Number Registry.

Check and block port 4405

Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.

Check on Linux

sudo ss -tlpn 'sport = :4405' sudo ss -ulpn 'sport = :4405'

Check on Windows

Get-NetTCPConnection -LocalPort 4405 -State Listen -ErrorAction SilentlyContinue Get-NetUDPEndpoint -LocalPort 4405 -ErrorAction SilentlyContinue

Block with UFW

sudo ufw deny 4405/tcp sudo ufw deny 4405/udp

Block with iptables

sudo iptables -A INPUT -p tcp --dport 4405 -j DROP sudo iptables -A INPUT -p udp --dport 4405 -j DROP

These commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.

Is port 4405 safe to expose?

Standard/Low

This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.

Where port 4405 is usually used

Most traffic on port 4405 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.

Demo

Probe the control-plane service

These services are high-value targets. Verify the listener from a trusted host before changing firewall rules.

nc -vz 127.0.0.1 4405

Common problems with port 4405

Connection refused or timed out

Refused usually means the host is reachable but nothing is listening on port 4405. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.

Port already in use

Find the process holding the port with sudo ss -tlpn 'sport = :4405' or sudo lsof -i :4405. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.

Firewall rule did not survive a reboot

UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.

The port is blocked but still reachable

A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.

Port 4405 at a glance

Port number4405
Service nameds-mail
Transport protocolTCP / UDP
CategoryInfrastructure and administration
RangeRegistered port (1024–10000)
Risk levelStandard/Low
Registered assigneeNot listed
Registry descriptionASIGRA Televaulting Message Level Restore service
SourceIANA Service Name and Transport Protocol Port Number Registry

Frequently asked questions

What is port 4405 used for?

Port 4405 (DS-MAIL) uses TCP / UDP. ASIGRA Televaulting Message Level Restore service.

How do I check if port 4405 is open?

On Linux run `sudo ss -tlpn 'sport = :4405'` and `sudo ss -ulpn 'sport = :4405'`. On Windows run `Get-NetTCPConnection -LocalPort 4405 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 4405 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 4405; empty output usually means nothing is bound to it.

How do I block port 4405?

With UFW run `sudo ufw deny 4405/tcp` and `sudo ufw deny 4405/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 4405 -j DROP` and `sudo iptables -A INPUT -p udp --dport 4405 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.

Is port 4405 safe to expose?

This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.

See all Infrastructure and administration ports

Primary data: IANA Service Name and Transport Protocol Port Number Registry.

Last reviewed 2026-10-30 · Methodology · About · Privacy