Port 5638 FLCRS
Port 5638 is the IANA-assigned flcrs port for Symantec Fingerprint Lookup and Container Reference Service (TCP).
What is port 5638 used for?
Port 5638 is assigned to flcrs and uses TCP. The IANA registry describes the service as “Symantec Fingerprint Lookup and Container Reference Service”. It sits in the registered range, the block used by databases, application servers and developer tooling. Port conflicts here are common when several local services start at once.
Ports are the transport-layer address a service listens on. A client that wants to reach flcrs connects to port 5638. If nothing is listening, the connection is refused. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 5638 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Browse all Containers and orchestration ports
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Symantec_Corp].
Check and block port 5638
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :5638'Check on Windows
Get-NetTCPConnection -LocalPort 5638 -State Listen -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 5638/tcpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 5638 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 5638 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 5638 is usually used
Most traffic on port 5638 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Cluster control-plane traffic and automation clients managing workloads.
- Operators inspecting nodes, pods and secrets from a trusted network.
- CI pipelines deploying manifests against a cluster endpoint.
Check the cluster endpoint
Use the vendor CLI with the kubeconfig that already knows the endpoint; a raw probe only proves the socket is open.
kubectl cluster-infoCommon problems with port 5638
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 5638. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :5638' or sudo lsof -i :5638. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 5638 at a glance
| Port number | 5638 |
|---|---|
| Service name | flcrs |
| Transport protocol | TCP |
| Category | Containers and orchestration |
| Range | Registered port (1024–10000) |
| Risk level | Standard/Low |
| Registered assignee | [Symantec_Corp] |
| Registry description | Symantec Fingerprint Lookup and Container Reference Service |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 5638 used for?
Port 5638 (FLCRS) uses TCP. Symantec Fingerprint Lookup and Container Reference Service.
How do I check if port 5638 is open?
On Linux run `sudo ss -tlpn 'sport = :5638'`. On Windows run `Get-NetTCPConnection -LocalPort 5638 -State Listen -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 5638; empty output usually means nothing is bound to it.
How do I block port 5638?
With UFW run `sudo ufw deny 5638/tcp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 5638 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 5638 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 5635 · sfmssoSFM Authentication Subsystem
- Port 5639 · icsSymantec Integrity Checking Service
- Port 4665 · contclientmsContainer Client Message Service
- Port 6443 · sun-sr-httpsService Registry Default HTTPS Domain
- Port 2380 · etcd-serveretcd server to server communication
- Port 10250 · Kubernetes kubeletKubernetes kubelet HTTPS API port on each node (community convention;…
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy