Port 900 OMGINITIALREFS
Port 900 is the IANA-assigned omginitialrefs port for OMG Initial Refs (TCP / UDP).
What is port 900 used for?
Port 900 is assigned to omginitialrefs and uses TCP / UDP. The IANA registry describes the service as “OMG Initial Refs”. It sits in the well-known range, which operating systems reserve for core network services, so software expects it at this number by default.
Ports are the transport-layer address a service listens on. A client that wants to reach omginitialrefs connects to port 900. A TCP connection is refused when nothing is listening, while a UDP request simply goes unanswered. That is why a port conflict appears whenever two processes try to bind the same number.
Use the commands below to confirm whether port 900 is actually in use before you change firewall rules. Blocking the port stops new inbound traffic at the firewall, but it does not stop a local process from listening, and it does not remove the service from the machine.
Source: IANA Service Name and Transport Protocol Port Number Registry. Registered assignee: [Christian_Callsen].
Check and block port 900
Copy-ready commands for the protocols assigned to this port. Run the check first, then block only what should not be reachable.
Check on Linux
sudo ss -tlpn 'sport = :900'
sudo ss -ulpn 'sport = :900'Check on Windows
Get-NetTCPConnection -LocalPort 900 -State Listen -ErrorAction SilentlyContinue
Get-NetUDPEndpoint -LocalPort 900 -ErrorAction SilentlyContinueBlock with UFW
sudo ufw deny 900/tcp
sudo ufw deny 900/udpBlock with iptables
sudo iptables -A INPUT -p tcp --dport 900 -j DROP
sudo iptables -A INPUT -p udp --dport 900 -j DROPThese commands are examples for a typical host. Check the listener before you change firewall rules, and persist iptables rules with iptables-save or netfilter-persistent. On Windows, use Windows Defender Firewall or New-NetFirewallRule for persistent blocks. The iptables rules here cover IPv4; mirror them with ip6tables if IPv6 is enabled.
Is port 900 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Where port 900 is usually used
Most traffic on port 900 falls into these scenarios. The demo below is a safe way to confirm the listener before you change anything.
- Core infrastructure that clients expect to find at its default number.
- Firewall reviews that baseline which classic services are reachable.
- Troubleshooting connectivity when an application assumes the standard port.
Probe the port
Confirm something is listening before you debug the client. Replace 127.0.0.1 with the host you are testing.
nc -vz 127.0.0.1 900Common problems with port 900
Connection refused or timed out
Refused usually means the host is reachable but nothing is listening on port 900. A timeout more often means a firewall drop, a wrong host or a service bound to a different interface.
Port already in use
Find the process holding the port with sudo ss -tlpn 'sport = :900' or sudo lsof -i :900. Stop that process or configure it to bind another port; killing it without identifying it can take down a production service.
Firewall rule did not survive a reboot
UFW and Windows Firewall keep rules across restarts. Raw iptables rules do not: save them with iptables-save or the netfilter-persistent package, and re-apply after upgrades that reset the ruleset.
The port is blocked but still reachable
A firewall rule filters inbound traffic; it does not close the listener. Confirm with the check command above and bind the service to 127.0.0.1 when only local clients need it.
Port 900 at a glance
| Port number | 900 |
|---|---|
| Service name | omginitialrefs |
| Transport protocol | TCP / UDP |
| Category | Core network services |
| Range | Well-known port (0–1023) |
| Risk level | Standard/Low |
| Registered assignee | [Christian_Callsen] |
| Registry description | OMG Initial Refs |
| Source | IANA Service Name and Transport Protocol Port Number Registry |
Frequently asked questions
What is port 900 used for?
Port 900 (OMGINITIALREFS) uses TCP / UDP. OMG Initial Refs.
How do I check if port 900 is open?
On Linux run `sudo ss -tlpn 'sport = :900'` and `sudo ss -ulpn 'sport = :900'`. On Windows run `Get-NetTCPConnection -LocalPort 900 -State Listen -ErrorAction SilentlyContinue` and `Get-NetUDPEndpoint -LocalPort 900 -ErrorAction SilentlyContinue` in PowerShell. If the port is open, the output shows a process listening on port 900; empty output usually means nothing is bound to it.
How do I block port 900?
With UFW run `sudo ufw deny 900/tcp` and `sudo ufw deny 900/udp`. With iptables run `sudo iptables -A INPUT -p tcp --dport 900 -j DROP` and `sudo iptables -A INPUT -p udp --dport 900 -j DROP`. Persist the iptables rules with your distribution's netfilter-persistent or iptables-save tooling so they survive a reboot.
Is port 900 safe to expose?
This port is not on our curated list of services with a widely exploited profile. Exposure is only safe when the listening service is intended, patched and protected by a firewall. Nevertheless, keep the listening service patched and remove it if unused. A default-deny firewall policy with explicit allow rules is still the safest baseline.
Related ports
- Port 888 · cddbpCD Database Protocol
- Port 901 · smpnameresSMPNAMERES
- Port 887 · iclcnet-svinfoICL coNETion server info IANA assigned this well-formed service name…
- Port 886 · iclcnet-locateICL coNETion locate server
- Port 902 · ideafarm-doorself documenting Door: send 0x00 for info
- Port 862 · twamp-testTWAMP-Test Receiver Port
Primary data: IANA Service Name and Transport Protocol Port Number Registry.
Last reviewed 2026-10-30 · Methodology · About · Privacy